MB Star SD Connect C4 VS SD Connect C5

I. The software of MB SD Connect 5 and MB SD Connect 4 is same
II. But the hardware of MB SD C5 is better and stable than MB SD C4:

1. The host CPU radiator surface and perfectly fit alloy shell, good heat dissipation effect. Equipment running smoothly, don’t crash.
2. The host USES the tamper clasp, should to avoid fragile warranty sticker damage caused by the warranty disputes.
3. Host wi-fi protected the upgrade for PC plastic shell, solid quality does not affect the wi-fi signal.
4. The host communication connection end USES from design, to avoid inadvertently fall in the normal use of the communication port to connect and communication failure, etc.
5. DC 12 v power supply design/host upgrades to avoid the battery installation/battery voltage instability/host can’t enter the shutdown state, etc, caused by the motherboard and rapid aging of the battery.
6. OBD main telecommunication lines connected to the host end upgraded to VGA15 industrial-grade connector.
7. Network upgrade for gigabit connections/pure copper wire core/double layer aluminum foil/woven mesh/silica insulation material. Gigabit communication Against interference/pulling open circuit / / fracture in low temperature.



MB SD Connect C5 is Verified Working Great

The new Mercedes Benz diagnostic tool MB SD Connect C5 clone is verified working great. Here are customer feedback to Benz C5 SD Connect (not original Xentry Connect C5).


“Mercedes Sprinter year 2006 and 2014 works, both the diagnosis

All the personal cars also works, no problem”


“All the trucks including euro6 also works, no problem.

Bus Mercedes Tourismo euro5 year 2010-2012 test works, BUT year 2014 euro6 does NOT work, it says that the license is invalid. Both sd c4 and sd c5, we have tested both on the same cars, to be sure.”


SD Connect C5 this one customer has test, works good, in function it no difference with SD C4, but performance it is better. So you can buy MB SD C5 if you want buy new MUX. SD C5 use the same software as MB SD Connect C4.

Toyota G and H Chip OBD Remote Key Programming Feedback

Will this Toyota G and Toyota H Chip OBD remote key programming device add key for Avalon 2000? Can it do all keys lost?

Obd2sale engineer solution:
The supported car is determined by car key chip type, not exactly models. The device will add key with 4D67, 68 ,72(G) chip, supports both G and H chip via OBD2 port. Tested great on Camry 2015. No software, laptop or other accessories required. Can only add key, not for all keys lost.

Customer Feedback:

Product worked as advertised.
This is a 2 step process-Transponder programmer to have the key work with the car’s security system and Remote programmer to have the lock/Unlock/Trunk/Emergency for key buttons to work with car. This unit handles both programming tasks.
Toyota wanted $350 per key, local locksmith wanted $250 for 2 keys. This device save me much.

Add Toyota remote control

Get in the car and close the door, insert the key and turn on the key, insert the device into OBD. After the sound(Dee-), it will start to add the remote control.
After the sound ( Dee- Dee-),open the door, when hear the sound blaring. Press ‘ lock & unlock’ key at the same time. And press the’ lock’ key. If the blaring ends, It’s OK.

Note: Switch is on the right.(add remote control)


Add Toyota transponder:

Get in the car and close the door, Toyota G and Toyota H Chip insert the main key into the lock and turn the key on,and then insert the device into the OBD. If it will sound twice, it will start to add transponder.
After the sound (Dee-Dee-), 2-3 minutes later, anti-theft light is on. And then remove the key( anti-theft light will flash), insert the new key and doesn’t need turn the key,anti-theft light will be off later.

Note: switch is on the left.( add transponder)

How to Program Toyota G Chip Key with SKP900

Here is the step by step instruction on programming Toyota G chip key by using SuperOBD SKP900 key programmer.

You need prepare the register main key and new key for use.



Then onnect SKP-900 device to the car


The immo lamp on the car falshes


Then start SKP900





Choose OBDII adapter and turn ignition on




Add key


Insert the registered main key and turn ignition on


Insert the adding key and turn ignition on


Program succeed after immo lamp extinction





Insert the new key to test- it’s working



TOYOTA G chip programming success!