How to used Xhorse VVDI2 Key Programmer check Points

Xhorse VVDI2 Copy 48 Transponder (96 Bit) Authorization comes with with free MQB License and 1500 bonus points. How to check points in VVDI2?

Top 5 Reasons to Get VVDI2 Auto Key Programmer 

1. This Xhorse VVDI2 comes with Basic Function + VW + Porsche+ AUDI Generation 5 function+BMW OBD Fucntion+BMW CAS4 function  , No Need to buy other Authorization. You may only need the cas plug to work with vvdi2(Item number SK108-B)
2. VVDI2 Covers All the Functions of VVDI, VVDI 5th IMMO Adapter, BMW Multi Tool, CAS4 Adapter, Most functions of Tango, J2534
3. Support VW, Audi, BMW and Porsche
4. Provide Exchange Service for Old VVDI,Item number: SV86-1
5. Newest Version: V5.2.5
6. Pls note VVDI2 FULL not include the vag 48 copy and BMW FEM authorization. Need to buy extrally if you need

Notes:
1.backup coding and restore coding can direct operation generally.
2.add keys, reset KM, erase key must programming FEM/BDC system first
3.in FEM/BDC interface, if ‘get key info’ the type not support, it will show:customer should use “BMW E-sys software” program FEM/BDC system.then programming FEM/BDC system with VVDI2-BMW
4.when operation on ‘programming FEM/BDC system’interface,please don’t close this software window until all procedures completed.
5.programming FEM/BDC system, require soldering and get eeprom.(FEM 95128 chip, BDC 95256 chip)usually there are 2 same chips on the module, please refer to the software diagram, select the correct one.
6.programming FEM/BDC system,must restore the original eeprom, restore coding.if cannot restore coding or after restore coding assemble FEM/BDC module back to car,but with problem(such as the remote control cannot start the car
or the car with window problem)please use “BMW E-sys software” coding for FEM/BDC system
7.if connect power to FEM/BDC module, but the relay keep ringing,please contact technical support for help.usually operation on FEM/BDC should be ok,just need to programming.

Update your VVDI2 software to latest version, provide Serial Number and buy license to activate ID48 96-bit function.

Open VVDI2 Quick Loader

check-vvdi2-points-1

Select Transponder Programmer

check-vvdi2-points-2

check-vvdi2-points-3

You’ll see Points System tab

Check bonus points

check-vvdi2-points-4

check-vvdi2-points-5

http://www.fobdii.com

 

Which better VVDI2 BMW vs CGDI Prog BMW For BMW key programming

Both Xhorse VVDI2 and CGDI Prog are able to work well in BMW immobilizer. So, what’s the difference of both tools in terms of BMW key programming? which better?

First, The biggest difference!!!!!!!!!

VVDI2 BMW vs. CGDI BMW

IMMO VVDI2 BMW CGDI BMW
EWS Yes No
CAS Yes Yes
FEM Yes Yes
EDC Yes Yes

Note 1: VVDI2 can work for old cars with EWS immo, incl. EWS1/EWS2/EWS3/EWS4

CGDI Prog cannot work for cars with EWS immobilizer systems.

Note 2: Both VVDI2 and CGDI Prog supports CAS1/CAS2/CAS3/CAS3+/CAS4/CAS4+

Note 3: Model with EWS: E31/E34/E36/E38/E39/E46/E52/E53:

EWS, E36 9/93-12/93 = links the door lock switch to the DME and OBC. If the door was locked with the key (or factory alarm) the car will not start without the doors unlocked with the factory key or entering the code into the OBC. In other words, you can’t smash the window and hot wire the car because the DME has killed the ignition and fuel systems.

EWS-I, E36 1/94-12/94 = same as above but added a starter immobilization relay and transmission position switch.
In either of the above systems the DME is passive. It only receives signals from sensors and modules. So the DME is not as tied into the body electronics as much as EWS-II.

EWS-II, E36 1/95-8/96 = similar to the above but with an electronic key, EWS module (“brain”), and the DME all linked together. The same door lock logic remains. All systems for starting the engine are run through the EWS module (starter relay, starter power, fuel, ignition). The key sends a signal to the EWS module and the module asks for a matching signal from the DME. If the two signals don’t match the EWS module will not start the car. The EWS module also checks for OBC function and transmission park/neutral position.

EWS-III, E36 9/96-8/99 = revised EWS-II system with added clutch position sensor and revised module and wiring.

Second, VVDI2 and CGDI differs in authorization & price

Xhorse VVDI2 BMW : 1049USD

The kit comes without OBD function and basic function (Transponder Auto Key Programmer  and Passthru J2534).

BMW FEM/BDC and CAS4+ Function is not available.

Unlimited use once the function is authorized.

CGDI Prog BMW : 698USD

The programmer comes with OBD, FEM/BDC and CAS4+ function; price included

In the long run, Xhorse vvdi2 will help save a lot, esp for those working for a workshop or auto repair garage.

But if you’re a DIYer, CGDI BMW is cost-effetive.

which tool BMW FEM BDC system KM reset

Post is on which tool best to change KM in BMW FEM BDC system? and how to do?

Tools Option:

Xhorse VVDI2 (Pay extra money for BMW FEM/BDC authorization)

Yanhua FEM/BDC Programmer V1.4

BMW Explore

Guide:

  1. How to use Xhorse VVDI2 to change KM in BMW FEM BDC?

Xhorse VVDI2 V4.3.0 supports reset FEM/BDC KM(cluster require reset manually).

VVDI2 V4.3.0 download free:

https://mega.nz/#!W1pSRRTL!0n8OX4wshaB1s0O06SDhTR0KvO32nPHZWg4CQjBMdrA

vvdi2-bmw-4.3.0-update-01

vvdi-bmw-v4.3.0-fem-bdc-reset-km-02

How to Reset KM in FEM/BDC system?

Just follow the steps on the screen if you have no idea.

Price: Extra 600-800dollars to authorize FEM/BDC.

  1. Guide: BMW FEM BDC KM reset with Yanhua FEM/BDC Programmer V1.4

yanhua-bmw-fem-key-programmer

Since Yanhua FEM/BDC Programmer V1.4 update, KM reset is working.

Yanhua FEM/BDC Auto Key Programmer source:

http://www.fobdii.com/wholesale-509-yanhua-bmw-fem-key-programmer.html

& software V1.4 with FEM BDC KM reset download:

http://www.autoecu.com.cn/download/page.do

OS: XP/Win7/Win10

Files contained:

yh-bmw-fem-bdc-km-reset

Using tips:

The software and hardware must update all!!!

The step as follow:

  1. install BMW_FEM_BDC_EN_V1.0.4.msi
  2. run BMW_FEM_BDC.exe
  3. click “Upgrade adapter”, select the upgrade file: BMW-FEM-V14.bin
  4. follow the tip, wait for upgrade complete